HOME
HEATING
COOLING
WASTE OIL
AIR QUALITY
SERVICE
ABOUT



Lanair Replacement Parts
Free Shipping on All Online Purchases!


SEARCH

ADAPTOR BLOCK KIT FI/HI/MX #9867

The Adaptor Block is a non-serviceable part, and should be replaced when the annual tune up is performed. See the tune up kit for you model of furnace below for a better value.

$39.99

Back to Parts List

ADAPTOR OIL BLOCK FI/HI/MX #9029

This Adaptor is used to connect your fuel line, and oil pre
ssure gauge to the oil preheater block. Two are required. The Viton® o-ring that is on this adaptor is included in the in the oil preheater o-ring kit.

$8.30

Back to Parts List

AIR PREHEATER O RING KIT FI/HI/MX #9870

The air preheater is the upper aluminum block inside your burner.This kit includes all of the Viton® o-rings, Viton® quad ring, seal, spring and fasteners for tuning up the air preheater block. Find the tune up kit below for your model of furnace for a better value.

$30.92
Back to Parts List

BAROMETRIC DAMPER 6" - 8" #0005

The Barometric Damper is required to maintain proper draft. The Barometric Damper automatically maintains a pre-set chimney draft after being set with a manometer.

$78.85

Back to Parts List

BLOCK OIL FI/HI/MI/MX #29012901

101.70

Back to Parts List

BLOWER WHEEL FI/HI/MX #9877

The Blower Wheel is used to provide combustion air to the burner.

$25.05
Back to Parts List

BRICK 180/260 #2666

117.26

Back to Parts List

BY-PASS REGULATOR LARGE #9570

The By-Pass Regulator regulates the flow of fuel to the burner.

$92.25
Back to Parts List



CABINET ASSEMBLY DHI300 #3198

$319.14

Back to Parts List

CAD CELL CA/FI/HI/MX #8981

The Cad Cell can also be called a Flame Sensor. If the Cad Cell does not see light from the flame the Oil Primary Control will shut the burner off after 30 seconds.

$38.42

Back to Parts List

CARTRIDGE HEATER AIR FI/HI FI/HI/MX #9856

The Air Cartridge Heater is located in the upper aluminum block of the pre-heater assembly. The Air Cartridge Heater heats the air and oil to a specified temperature prior to being burned. The Air Cartridge Heater temperature is controlled by the snap disc see below.

$135.98
Back to Parts List


CARTRIDGE HEATER OIL FI/HI/MX #8992

The Oil Cartridge Heater is located in the lower aluminum block of the pre-heater assembly. The Oil Cartridge Heater heats the oil to a specified temperature prior to being burned. The Oil Cartridge Heater temperature is controlled by the snap disc see below.

$120.50
Back to Parts List


CHAMBER COMBUSTION ASEM HI 260 #3176

$869.61

Back to Parts List


COMBUSTION BLOWER ASSEMBLY FI/HI #9862

The Combustion Blower Assembly includes the Combustion Blower, and the blower wheel. The Combustion Blower Assembly is located in the burner, and provides air for combustion.

$230.00
Back to Parts List


COMBUSTION CHAMBER GUN DOOR ASSEMBLY HI 180/260 #32543254

This is the combustion chamber door that the main burner assembly mounts to. Comes complete with gaskets.

$155.00

Back to Parts List


COMBUSTION CHAMBER REPAIR KIT FOR HI 180/260 #10053WB10053WB

This repair kit is designed to repair a heat damaged combustion chamber on a Lanair HI 180 or 260. If your chamber has a hole burned in the end, this is the way to go. It is an easy pre-formed weld-in metal panel and a full-size, 2 inch thick ceramic refractory target pad rated for 2100 degrees Fahrenheit. No need to remove the damaged area, just flatten and weld in the new panel.

$279.00
Back to Parts List


CONTROL FAN LIMIT #8402

The Control Fan Limit performs two functions. It controls when the fan or blower comes on, and shuts off based on temperature. It also shuts the burner off if the fan or blower fails.

$98.85

Back to Parts List

COUPLER PUMP A1RA #88818881

The Coupler is used to transfer power from the electric motor to the pump head on the pump assembly. This coupler is only used on the standard A1RA pump head. When changing the coupler it is also a good time to service your pump. See pump gasket, and screen below.

$9.99

Add to Cart
Back to Parts List

COUPLER PUMP A1RA #8881 HDCOUPLER

Heavy duty pump coupler.

$29.99

Back to Parts List

 

COUPLER PUMP J #2791

The Coupler is used to transfer power from the electric motor to the pump head on the pump assembly. This coupler is only used on the upgrade J pump head. When changing your coupling it is also a good time to service your pump. See pump gasket, and screen below.

$25.30


DIAPHRAGM KIT FI/HI/MX #9871

The Diaphragm Kit includes the Viton? diaphragm and o-rings, as well as the spring and fasteners to rebuild the diaphragm assembly.

$30.92



GASKET FACE PLATE A1RA PUMP #9817

The Pump Face Gasket is used to seal when cleaning the internal screen of the pump. This gasket is only used on the standard A1RA pump head.

$8.40

Back to Parts List


FLANGE GASKET #8732

The Flange Gasket is used to seal the burner to the combustion chamber of the furnace.

$13.50

Back to Parts List

FLANGE GASKET MX SERIES #3952 flange gasket

Gasket between burner assembly and heater cabinet.

$23.50

Back to Parts List

FLEXIBLE FUEL CONNECTOR HI SERIES #10002WB Fuel Connector

This 24" flexible hose goes between the fuel pressure regulator and the burner. No need to remove this hose to swing the burner assembly open. Less mess.

$40.00

Back to Parts List


FLEXIBLE FUEL CONNECTOR MX SERIES #10001WB flange gasket

This 46" flexible hose goes between the fuel pressure regulator and the burner. No need to remove this hose to swing the burner assembly open. Less mess.

$46.00

Back to Parts List


GASKET CLEAN OUT HI 320 #3087

$55.80

Back to Parts List

GASKET GUN PANEL HI 320 #3086

$55.80

Back to Parts List

GASKET INSPECTION PORT ROUND CA/FI/MX 250/300 #2399

$5.78

Back to Parts List

GAUGE AIR PSI 0-30 #8451

The Air Gauge is used in conjunction with the secondary air regulator to control compressed air to the burner.

$32.00

Back to Parts List
GAUGE OIL PSI 0-15 #8430 8430

The Oil Gauge is located on the side of the burner, and is used as a reference for adjusting fuel pressure. Remember to visually adjust your flame as outlined in your owner's manual.

$31.95

Back to Parts List

KIT BRICK HI 260/320 #3195

$454.82

Back to Parts List

KIT CLEANOUT DOOR HI 320 #3196

$111.35

Back to Parts List

KIT CLEANOUT DOOR INSUL 240/32 #3197

$255.02

Back to Parts List

KIT INSULATION REPLACE HI 140 UL #3192

$31.75

Back to Parts List

KIT INSULATION REPLACE HI 180/2 #3191

$70.61

Back to Parts List
IGNITOR ASSEMBLY ONE PIECE FI/HI/MX #3728

The Ignitor transfer power from the transformer to the tips of the Ignitor where they produce a constant spark. This spark ignites the atomized fuel. The Ignitors may wear over time and should be replaced when you do your annual burner tune up. When replacing ignitor it is also a good time to replace your nozzle. See the tune up kit below for your model furnace for a better value.

$49.99

Back to Parts List
KIT BY-PASS REBUILD REGULATOR #9874

The Kit By-pass Rebuild includes all of the internal components to rebuild the aluminum by-pass valve (fuel pressure regulator).

$25.00

Back to Parts List
KIT TUNE UP HI 180/260 #9058

This kit contains everything needed to do the tune up of your burner, including:

  • 1- Oil pre heater o-ring kit #9869
  • 1- Air pre heater o-ring kit #9870
  • 1- Diaphragm with o-rings kit #9871
  • 1- Adaptor block kit #9867
  • 1- All brass nozzle assembly with quad ring (customer please specify the furnace model for proper nozzle)
  • 1- Air turbulator #9853
  • 1- A-pump coupling # 8881
  • 1- A-pump face plate gasket #9817 (J-pump face plate gasket upon request no additional charge)
  • 1- Burner mounting flange gasket
  • 1- One piece ignition electrode #3728
  • 1- Pre heater temperature control snap switch kit #9533
  • 1- Main strainer o-ring #9043

This kit comes with complete parts breakdowns and instructions.

$299.99

Back to Parts List
KIT TUNE UP HI 140/320/MX #9059

This kit contains everything needed to do the tune up of your burner, including:

  • 1- Oil pre heater o-ring kit #9869
  • 1- Air pre heater o-ring kit #9870
  • 1- Diaphragm with o-rings kit #9871
  • 1- Adaptor block kit #9867
  • 1- All brass nozzle assembly with quad ring (customer please specify the furnace model for proper nozzle)
  • 1- Air turbulator #9853
  • 1- A-pump coupling # 8881
  • 1- A-pump face plate gasket #9817 (J-pump face plate gasket upon request no additional charge)
  • 1- Burner mounting flange gasket
  • 1- One piece ignition electrode #3728
  • 1- Pre heater temperature control snap switch kit #9533
  • 1- Main strainer o-ring #9043

This kit comes with complete parts breakdowns and instructions.

$299.99

Back to Parts List

MAIN STRAINER COMBU SEAL KIT #90258108

The seal kit for the Combu brand main strainer.

$30.00

8108
Back to Parts List

MOTOR 1/4 HP ELECTRIC #81088108

This Motor is used to run the pump assembly.

$160.99

8108
Back to Parts List
NEON SWITCH FI/HI/MX PREHEATER #9529

The Neon Switch is used to operate the preheater, and is located on the rear of the burner. This switch should be on when burning waste oil, and off when burning fuel oil.

$12.00

Back to Parts List
NOZZLE ASSEMBLY HI 140/240/320 #9899

The function of the Nozzle is to mix the air and oil atomizing it into the combustion chamber allowing it to burn. The Nozzle should be replaced during the annual tune up. See Kit Tune Up HI 140/240/320 for a better value.

$64.30

Back to Parts List

NOZZLE ASSEMBLY HI 100/140i/180/260 MX150/200/250/300 #98529899

$63.80

Back to Parts List


OIL BLOCK ASEM PLUGGED FI/HI/MI/MX #2902

$107.70

Back to Parts List
O RING 8942/9807 STRAINER #9043

This O-ring is used to seal the primary strainer.

$8.96

Back to Parts List
OIL PREHEATER O-RING KIT FI/HI/MX #9869

The oil preheater is the lower aluminum block inside your burner. This kit includes all of the Viton? o-rings, and fasteners for tuning up the oil preheater block. This assembly should be rebuilt annually after every heating season. See the tune up kit for your model of furnace below for a better value.

$29.35

Back to Parts List
OIL PRIMARY CONTROL #8980

The Oil Primary Control is mounted on top of the burners electrical box. It works in conjunction with the thermostat, and the cad cell. When the thermostat calls for heat the Oil Primary Control starts the burner by switching on the solenoid valve, ignition transformer, combustion air blower, and the fuel pump. If the cad cell fails to see a flame the Oil Primary Control will shut the burner off after 30 seconds. After another 90 seconds the Oil Primary Control will attempt to restart the burner. If a flame is not established in 30 seconds the Oil Primary Control will lock out on safety, and will have to be manually reset.

$140.00

Back to Parts List
PREHEATER ASSEMBLY FI/HI 180/260/300 #9811

The Preheater Assembly is test fired and ready to install into your burner. The Preheater assembly includes new aluminum blocks, plunger, diaphragm, adaptor block, ignitors, nozzle, cartridge heater, turbulator and snap disc.

$399.99

Back to Parts List
PREHEATER ASSEMBLY HI 140/320/MX SERIES #9812

The Preheater Assembly is test fired and ready to install into your burner. The Preheater assembly includes new aluminum blocks, plunger, diaphragm, adaptor block, ignitors, nozzle, cartridge heater, turbulator and snap disc.

$399.99

Back to Parts List
PUMP ASSEMBLY A1RA #2431

The Pump Assembly is used to transfer waste oil from your tank to the burner. This is a complete assembly including the pump head, coupling, motor, bracket, and guard. This pump is designed for waste oil.

$522.71

Back to Parts List

PUMP MOTOR ASEM A1RA #2433

$418.26

Back to Parts List

PUMP HEAD A1RA #8234

The Pump Head is used to transfer waste oil from your tank to your burner. Be sure to fill your primary strainer as well as your all your lines before priming the pump. Before replacing the pump make sure you clean the screen under the face plate. Before replacing the pump head check your coupling and make sure its not worn, and slipping on the shaft of the motor or the pump head. When replacing the pump head replace the coupling at the same time.

$171.84

Back to Parts List

PUMP HEAD J #8235

The Pump Head is used to transfer waste oil from your tank to your burner. Be sure to fill your primary strainer as well as your all your lines before priming the pump. Before replacing the pump make sure you clean the screen under the face plate. Before replacing the pump head check your coupling and make sure its not worn, and slipping on the shaft of the motor or the pump head. When replacing the pump head replace the coupling at the same time. This Pump Head is designed and UL recognized for waste oil.

$301.25

Back to Parts List

PUMP SCREEN A1RA #9041

The Pump Screen is located under the face plate of the standard A1RA pump head. When cleaning this screen remember to replace the gasket (see below). This is also a good time to check the pump coupler.

$8.25

Back to Parts List

PUMP SCREEN J #9042

The Pump Screen is located under the face plate of the optional J pump head. When cleaning this screen remember to replace the gasket (see below). This is also a good time to check the pump coupler.

$12.15

Back to Parts List

QDC CORD ASSEMBLY HI 180/260 #82888286

This quick disconnect cord goes from the main electrical panel to the burner assembly.

$60.00


Back to Parts List


QDC CORD ASSEMBLY HI 320 #83268326

This quick disconnect cord goes from the main electrical panel to the burner assembly.

$60.00


Back to Parts List


QDC CORD ASSEMBLY MX SERIES #84898489

This quick disconnect cord goes from the main electrical panel to the burner assembly.

$60.00


Back to Parts List


QDC RECEPTACLE FOR FOR HI/MX SERIES #82868286

The quick disconnect receptacle for the burner assembly wiring.

$30.00

Paypal


Back to Parts List


REGULATOR NUT AND BRACKET #8428

The Regulator Nut holds the secondary air regulator on the bracket. It comes packaged with Regulator Bracket.

$13.95


Back to Parts List


REGULATOR/FILTER AIR #8450

The Regulator/Filter Air is used to adjust compressed air to the burner. This Regulator/Filter Air is a secondary Air Regulator used after the primary regulator. See your owner's manual for proper air setting for your model of furnace.

$79.26

Back to Parts List

SOLENOID ASSEMBLY FI/HI #9485 Paypal

The Solenoid Assembly controls the flow of compressed air to the pre-heater assembly. The Solenoid Assembly opens when the burner is operating. When the burner shuts off the Solenoid Assembly shuts off the flow of air to the pre-heater assembly allowing the plunger to close on the nozzle preventing oil from dripping into the chamber.

$93.38

Paypal
Back to Parts List
SNAP DISC KIT FI/HI/MX #9533

These switches control the oil pre heater temperature on all Lanair FI/HI/MX series heaters. Comes with instructions.

$79.00

Back to Parts List

STRAINER ELEMENT 100 mc #88448844

This Strainer is the main element before the pump. It should be cleaned annually.

$78.00

Back to Parts List

STRAINER 1/2" NPT SUCTION LINE #87488748

This Strainer is placed before the check valve 6" off the bottom of the tank. It keeps larger debris from entering the fuel lines. This Strainer should be cleaned annually.

$55.83

Add to Cart
Back to Parts List

STRAINER/FILTER 100 MC COMBU COMPLETE #98079807

$159.00

Back to Parts List
TANK ALARM #9255

Loud audible alarm. Easy installation. Can be set for high level, low level or leak detection. Can be add on to existing gauges. Lithium battery. Water resistant. This part number is for the alarm only for a combination gauge/alarm see below.

$81.00

Back to Parts List
TANK GAUGE #9254

Direct mechanical action, reliable construction and "at-a-glance" readability make this gauge a perfect choice for your Lanair Waste Oil Tank. Patented calibration assembly withstands pressure of 70 lbs. per sq. inch.Double plastic dome is almost indestructible. This Tank Gauge is made for a Lanair Waste Oil Tank, or other 36" deep tanks with a 2" bung.

$39.99

Back to Parts List
TANK GAUGE/ALARM COMBINATION #9256

GAUGE Direct mechanical action, reliable construction and "at-a-glance" readability make this gauge a perfect choice for your Lanair Waste Oil Tank. Patented calibration assembly withstands pressure of 70 lbs. per sq. inch. Double plastic dome is almost indestructible. This Tank Gauge is made for a Lanair Waste Oil Tank, or other 36" deep tanks with a 2" bung.

ALARM
Loud audible alarm. Easy installation. Can be set for high level, low level or leak detection. Can be add on to existing gauges. Lithium battery. Water resistant.

$99.00

Back to Parts List
TANK TOP FUNNEL WITH STRAINER AND LID #10003WB 10003WB

This large tank top funnel is heavy duty and stable. Fits a 2 inch opening on any flat top tank

$89.00

Back to Parts List
TERMINAL BLOCK ASSEMBLY FI/HI #8294

The Terminal Block Assembly is located inside the Burner. It is the junction for all the electrical connections inside the burner. Wires can be disconected from the terminal block by inserting a small flat screwdriver into the opening above the wire and pushing. As with all electrical wiring, disconnect power to the furnace before working on it.

$34.65

Back to Parts List

THERMOSTAT LOW VOLTAGE #9037

The Thermostat is a switch turns the furnace on and off based on the setting and room temperature.

$61.50

Back to Parts List

TRANSFORMER ELECTRONIC SS #8856

The Transformer creates the spark to ignite the fuel through the ignitors. See your owner's manual for the proper adjustment of the ignitors. This Transformer may look different than the one you currently have, but it is a replacement for all models of furnace that operate on 120V.

$130.00

Back to Parts List


TURBULATOR ASSEMBLY FI/HI/MX #9853

The Turbulator Assembly mixes the combustion air with the atomized fuel in the combustion chamber. The Turbulator needs to be replaced during the annual burner tune up. For a better value see Kit Tune Up for your model of furnace.

$50.00

Back to Parts List


VACUUM GAUGE #8398

The Vacuum Gauge is installed on the suction side of the fuel line. It us used to show when the primary strainer needs cleaning. The normal operating range is 1"-6" Hg. When the Vacuum gauge reads above this it may be time to clean the element in the primary strainer.

$40.00

Back to Parts List


VALVE CHECK 1/2" FPT #8662

The Check Valve is a valve that keeps your fuel lines full of oil eliminating the need to prime the pump on a regular basis. The Check Valve is located in the tank right after the suction line strainer. Remember to have the arrow on the side of the body of the Check Valve pointing in the direction of the fuel flow.

$40.00

Back to Parts List
WINDOW PLUG #9515

The Window Plug is located in the rear of the burner. It provides a window into the burner allowing you to see if you have spark, and to see if the burner is firing.

$5.25

Back to Parts List
 

| HOME | HEATING | COOLING | WASTE OIL | IAQP | SERVICE | ABOUT | EMPLOYMENT

©2007 West Brothers Inc.